行業資訊

裝載機行駛過程中變速箱“跳”的應急方式

來源：http://m.runbangpharm.com/ 日期：2022-12-14

在裝載機的行駛過程中，如果變速箱“跳”，濟南裝載機租賃廠家提醒您及時適時停止機器（或繼續行駛），然后找出緣故并排除故障。實際方式是：

During the driving process of the loader, if the gearbox "jumps", the Jinan loader rental manufacturer reminds you to stop the machine (or continue driving) in a timely manner, then find out the cause and remove the fault. The actual method is:

（1）在平緩的道路上行駛時，如果時有發生“變速”，則可以按照一般而言的停止方式使機器停止，并精心調查緣故，排除故障。

(1) When driving on a gentle road, if "shifting" happens occasionally, the machine can be stopped according to the general stopping method, and the cause can be carefully investigated to eliminate the fault.

（2）在上坡行駛時時有發生“換檔”時，可以將檔位設立在低速檔或第一檔，備用單元抵達坡頂時將停止，以排除故障。“如果降檔敗北或再度時有發生”，則在“換檔”時，根據斜坡的要點和要求停止，以掃除故障。

(2) When "shifting" occurs when driving uphill, the gear can be set at low speed or first gear, and the standby unit will stop when it reaches the top of the slope to eliminate the fault. "If the downshift fails or occurs again", stop according to the key points and requirements of the slope when "shifting" to remove the fault.

（3）在下坡行駛時時有發生“換檔”時，應根據升檔的動作要點將檔位設立為高速檔，或采取“抓檔”措施（緊急降檔），備用裝置應再度駛至斜坡底部停止以檢驗并排除故障；

(3) In case of "gear shifting" when driving downhill, the gear shall be set to the high gear according to the action point of upshift, or "gear holding" measures (emergency downshift) shall be taken, and the standby device shall be driven to the bottom of the slope again to stop for inspection and troubleshooting;
濟南裝載機租賃

如果“換檔”或“抓動”不成功或再度時有發生“換檔”（此時為空檔），駕駛員可以將引擎轉速操縱在中速（以防范引擎熄火），請用到“點制動”方式進行操作機器滑到斜坡的底部，然后進行故障排除。

If "shifting" or "grabbing" is unsuccessful or "shifting" occurs again (it is neutral at this time), the driver can control the engine speed at medium speed (to prevent the engine from stalling). Use the "spot braking" method to operate the machine to slide to the bottom of the slope, and then perform troubleshooting.

如果“變速”，“阻塞”未成功或再度時有發生“跳躍”（此時為空檔），并且機器降低了一個大坡道（機器將以非?？斓乃俣纫浦列逼碌牡撞浚?rdquo;），您應當根據下坡停車動作和要求很快停車，然后排除故障。

If "shifting", "blocking" is not successful or "jumping" occurs again (it is neutral at this time), and the machine lowers a large ramp (the machine will move to the bottom of the slope at a very fast speed) ", you should stop quickly according to the downhill parking action and requirements, and then troubleshoot.

裝載機行駛過程中變速箱“跳”的應急方式相關解答內容就到這里了，您平常使用中要及時進行檢查清潔。更多注意事項就來我們網站http://m.runbangpharm.com咨詢！

This is the end of the relevant answers to the emergency mode of the gearbox "jumping" when the loader is running. You should check and clean it in time during normal use. More notes on our website http://m.runbangpharm.com consulting service

上一條：路面機械設備出庫后的修理保養

下一條：加纖維瀝青混凝土的拌和要求